Full Spectrum Liquid Calcium (1/2 Gallon)
SKU: 66285576571

Full Spectrum Liquid Calcium (1/2 Gallon)

Sale price$32.40 Regular price$36.00
Save 10%

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Jul 6 - Jul 11

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

Full Spectrum Liquid Calcium (1/2 Gallon)Our Calcium is a product that is like basic calcium product competitors except it's carbon based and not chloride based. Calcium chloride can be detrimental to soils. While calcium chloride may be cheaper, it's not as efficient. Having a surfactant helps the efficiency, by moving through the soil profile while opening the soil for better aeration and water movement. This is beneficial for plant uptake and growth. Calcium is great for agriculture &

Our Calcium is a product that is like basic calcium product competitors except it's carbon-based and not chloride based. Calcium chloride can be detrimental to soils. While calcium chloride may be cheaper, it's not as efficient. Having a surfactant helps the efficiency, by moving through the soil profile while opening the soil for better aeration and water movement. This is beneficial for plant uptake and growth.

Calcium is great for agriculture & ornamental crops, athletic fields, golf courses, residential or

commercial lawns/gardens. This is high in available calcium to improve plant growth with balanced

nutrition. Calcium prevents tie-ups in soil because these nutrients are protected and will not lock-up in soils. It works to improve soil structure, prevent and treat soil conditions that are limited in water

infiltration. Improves calcium uptake & reduces surface tension of water, allowing the soil to drain.

Mixing Instructions:

  1. In a 5-gallon bucket, fill about halfway with water. Add in your rates of each product (1 product per bucket).
  2. Mix well. A drill with a paddle/paint mixer bit works the best.
  3. Add mixture to sprayer and dilute even more (at least 10gal of water per one gallon of Calcium)


Application Instructions:

  1. Calcium should be mixed with at least 10 gallons of water. We do not recommend letting the solution sit for an extended amount of time.
  2. Rinse out your sprayer with water when you are done spraying. It is also recommended that you remove all filters from your sprayer.


Generic Rates without recommendations or a soil sample: 1-2 quarts per acre

(we recommend getting your soil tested for more accurate & plot specific rates.)


GUARANTEED ANALYSIS:

Calcium Ca………………………….17.00%

Silicon as (SiO2)………………….1120ppm


$36 PER 1/2 GALLON JUG

Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 66285576571

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.1 ★★★★★
Based on 895 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
M
Verified Purchase
mattw
Massapequa, US
★★★★★ 4
Oily situation lol
Configuration: 4-Stroke, Size: 1 GA
Honestly how do you write a review of this product? I would have to run tests for years on multiple oils on various engines to do so. The value was good however and shipping was great
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 31, 2025
P
Verified Purchase
Peter Schott
Omaha, US
★★★★★ 5
Use the best oil to protect your investment
Configuration: 4-Stroke, Size: 1 GA
Great product.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on September 30, 2025
S
Verified Purchase
Steve M.
Bozeman, US
★★★★★ 5
Works well. You need to drill a 3/8” hole
Appears to be well made, alignment bar slides in nicely. As stated, you need to drill a hole in the bar for the gimble bearing driver, the directions are not clear, what I did was before I take out the old gimble bearing, put an O ring on the bar close to the last step on the bar, slide the bar all the way in, then carefully slide the bar out, this marks the distance from the back of the gimble bearing to where the shaft on the outdrive bottoms out, move the O ring a 1/4” towards the stepped part of the alignment tool (this is so you won’t bottom out the alignment tool when driving the gimble bearing in) then slide the driver puck up to the O ring and use a 3/8” diameter transfer punch through the side hole in the puck to mark the bar. You need to drill a 3/8” diameter hole in the alignment bar, two V blocks, some clamps, and a drill press will make drilling much easier, after the bar is securely mounted and centered in the drill press, use a center drill, then 1/4” drill first, using plenty of oil, drill all the way through, then use the 3/8” drill, deburr both sides and you should be good to go. People complain that it doesn’t come pre-drilled, the reason is that not all out drives are the same so you have to fit it to the outdrive that you have. Fortunately, I have a machine shop at my house and have a jig setup with various drill bushings, but the method I described above should work for you. Just make sure you’re perfectly centered and secure before you start drilling.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2026
N
Verified Purchase
Nancy filippi
Alexandria, US
★★★★★ 5
A must pull your gimbal bearing
You do need to drill a hole but worked perfect
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 26, 2025
R
Verified Purchase
rich911s
Waukegan, US
★★★★★ 5
Worked for Volvo Penta SX Gimbal Bearing
Very heavy tool, I was surprised. Pulled my bearing like it was nothing. Putting the new bearing in was a little more difficult as you have to drill a hole in the engine alignment shaft where it will work for your particular outdrive. Not hard, but it does not come pre-drilled as the required depth for each particular gimbal bearing differs by manufacturer and model. Measure your bearing placement before removal and check that it was installed correctly in the first place. The bearing should line up with the grease fitting and the o-rings on the drive shaft should end up riding in the middle of the bearing. once you have your measurement drill the hole, I used a drill press. I suppose you could use it on multiple outdrive models as long as you can drill more holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 5, 2023

recommand products